Hey everyone, I’m Jake, and I’ve been in the bolts and screws game for 8 years now. If you’ve ever spent 20 minutes staring at a pile of random washers, trying to figure out why your latest project’s leaking or wobbly, this post’s for you. Trust me, I’ve seen way too many people grab any old washer that fits the bolt’s size—only to end up with a mess that costs them time, materials, and even money. Today, I’m breaking down exactly how to pick the right washer, no fancy engineering degree required, and yeah, I’ll throw in a few pro tips that we’ve learned from answering 100+ customer questions every month here. Bolts and Screws

First off, let’s stop with the basic mistake: washers aren’t just “fancy spacers.” I see it all the time—someone orders a bolt, then grabs a random washer from their toolbox because it’s roughly the same hole size. But here’s the thing: washers do three core jobs, and picking the wrong one for any of them will tank your project. They spread the load so your bolt doesn’t dig into soft material, seal gaps to keep water or dust out, and prevent loosening from vibration (hello, engine parts or that wobbly fence post by your kid’s swing set). If you nail these three, you’re golden. If you skip them? You’ll be back redoing that job in 6 months.
Let’s start with the most obvious factor, but also the one that trips people up: size. I’m not just talking “fits the bolt’s diameter.” Wait, no—bolt sizes aren’t just their thickness, right? Like, a ¼” bolt is actually 0.25 inches, but what about the washer’s inner hole? If the hole’s even a hair too small, you’ll struggle to thread it on, and if it’s too big, the washer will wobble around and do literally nothing. We get so many messages that go, “Your ¼” washers don’t fit my bolts!” and half the time it’s because the guy measured the wrong part. Let’s keep this simple: for standard bolts, the inner diameter (ID) of the washer should be 0.01 to 0.02 inches larger than the bolt’s shank diameter. That’s the sweet spot. If it’s a metric bolt, like M6, go for an ID of 6.4mm—again, just a tiny bit bigger than the bolt. Don’t overcomplicate it, just check the product specs on whatever washer you’re buying, and match that to your bolt’s size.
Then there’s the outer diameter (OD). This is make-or-break for that load-spreading job. A small OD washer might look right, but if it’s too tiny, all that pressure from tightening the bolt will be concentrated on a ¼” spot, not spread out. It’s like standing on a single tile instead of the whole floor—way more likely to crack. For example, if you’re using a ½” bolt on a wooden deck, you need a washer with a big enough OD to cover the wood’s surface; otherwise, the bolt will pull right through the planks over time. Pro tip here: if you’re working with soft materials—wood, plastic, even thin metal—always go for a larger OD washer. We stock a lot of “oversize” washers for exactly this reason, and our regulars swear by them for decking, furniture, and DIY projects where soft surfaces are the norm.
Next up: material. This is where I see the most mistakes, especially from first-time builders. Washers are made for specific jobs, and grabbing a steel washer for a plumbing project is a fast track to leaks. Let’s break down the most common materials we carry, and when to use each:
First, steel washers. These are the workhorses, the ones most of us reach for first. They’re strong, cheap, and great for general projects—like assembling a metal shelf, or attaching a gate to a metal frame. But wait—there are two types of steel: plain steel and zinc-plated steel. Plain steel will rust if it’s even near moisture, so never use those outdoors or in a bathroom. Zinc-plated steel is coated to prevent rust, so it’s your go-to for fences, outdoor furniture, and even car parts that don’t get super hot. If you need something extra strong, we also have stainless steel washers. These are pricier, but they don’t rust at all—perfect for coastal areas (salt air is brutal on metal), plumbing, or any project where water is a given. I’ve seen guys buy cheap zinc washers for a boat dock, and within a year they’re completely corroded. Don’t be that guy.
Then there’s nylon washers. These are the weird, light-colored ones that look like plastic. When are these useful? If you’re working with something soft that might get scratched—like a wooden table, or even a car’s painted body. A steel washer would scratch the finish if you over-tighten, but nylon is soft enough to not damage surfaces. They’re also great for electrical projects, since nylon is an insulator—no risk of short-circuiting if the washer touches a wire. But here’s the catch: nylon isn’t strong. Don’t use it for heavy loads or high-vibration stuff. I tried a nylon washer once on my lawnmower blade bolt, and it fell off after a week—total disaster. Stick to nylon for light, delicate jobs, not engine parts.
Last, there’s bronze and copper washers. These are the fancy ones, mostly used for plumbing and gas lines. Copper is malleable, so it creates a tight seal when you tighten the bolt—no leaks. Bronze is similar, but stronger, so it’s good for higher-pressure lines. If you’re doing any plumbing work, a bronze washer is non-negotiable for a water heater or a pipe fitting. We get a lot of plumbers who only buy copper or bronze washers from us, and they tell me it cuts down on their call backs from leaky jobs. Worth the extra cost, if you ask me.
Now, here’s the part most people sleep on: washer type. There are like 10 different types, each for a specific job, and picking the wrong one is a secret cause of so many project failures. Let’s go over the ones you’ll actually use, no obscure industrial ones here:
Flat washers—we already talked about these, the standard, thin ones. Use them for general load spreading, when you just need to keep the bolt from digging in. That’s your everyday washer, 90% of the time this is what you need. But wait—what about lock washers? These are the split ring ones, right? They look like a broken circle. Their whole job is to stop bolts from loosening, which happens all the time with vibration—like on bikes, lawnmowers, or even your fridge’s compressor. Here’s the thing though: a lot of people overuse lock washers. If you’re tightening a bolt to spec (like for a shelf that doesn’t move), a flat washer is fine. If it’s something that vibrates, lock washers are great. But there’s a catch: some lock washers can damage the surface if you’re working with wood or paint. I once put a lock washer on a wooden sign I was hanging, and the sharp edges dug into the wood, making a tiny crack. So use lock washers for high-vibration metal projects, not delicate stuff.
Then there’s fender washers. These are extra-thin, extra-wide flat washers. You know the ones—used for attaching license plates, right? Wait no, actually, they’re for when you have a big hole or a thin surface. Like, if you’re attaching a thin metal bracket to a wall stud, a fender washer spreads the load over a bigger area so the bracket doesn’t pull through the drywall. We sell more fender washers for DIY wall mounts than any other type—guys go to hang a TV, grab a regular washer, and wonder why the drywall is cracking halfway through tightening. Fender washers fix that, easy.
Oh, and don’t forget about spring washers (sometimes called wave washers). These are different from lock washers—they’re not split, they have a wavy shape. They work a bit differently: when you tighten the bolt, the wave compresses, creating a small amount of tension that stops the bolt from loosening. Some people prefer these over lock washers because they don’t have sharp edges that can scratch surfaces. But again, same rule: only use them for vibration-heavy jobs. I use them on my bike handlebars, and they haven’t loosened in 2 years.
Wait, let’s talk about a common mistake with dual washers. A lot of guys put a lock washer and a flat washer together. Is that bad? Not always, but if you’re doing it because you think it’s “extra secure,” test it first. I’ve seen a lot of pros do it for critical jobs, but for 90% of DIY projects, one washer is enough. Adding an extra one just adds cost, and sometimes it can cause the bolt to not seat properly. Save the dual washer trick for engine parts or heavy machinery, not your bookshelf.
Now, let’s throw in a few real-world examples, because that’s what works for me. Last month, I got an email from a customer who was building a treehouse for his kids. He told me his bolts kept pulling through the cedar planks, even when he tightened them as hard as he could. What was he doing wrong? He was using standard ¾” OD steel washers, but he needed a 2-inch OD fender washer. The big OD spread the load over a way bigger area of the soft cedar, so the bolt didn’t dig in. We swapped his order, he installed it, and emailed me a week later saying the treehouse was rock solid. That’s the kind of problem that’s 100% fixable with the right washer.
Another example: a plumber who reached out a few months ago, saying he had leaky pipe fittings. He was using zinc washers for copper pipes, and the zinc was reacting with the copper, causing tiny gaps that leaked. I told him to switch to bronze washers, which are compatible with copper. He did, and he hasn’t had a leak on those fittings since. That’s a material mismatch, not a bolt size mistake—super common, so don’t skip checking the material compatibility.
Now, what about old projects where you’re fixing a mistake? If you’re undoing a job from 5 years ago that had a wobbly bolt, first check the washer. Chances are, either the size was wrong, or the material was wrong. A rusted washer on an outdoor project? That’s why it’s loose. A steel washer on a wooden fence? That’s why it dug into the wood and cracked. It’s way easier to replace the washer than to redo the whole installation.
Wait, let’s address the question we get all the time: “Can I use a washer that’s not the same material as my bolt?” Short answer: sometimes, but with caution. If your bolt is zinc-plated steel, a stainless steel washer is fine—no reaction there. If your bolt is copper, a bronze washer is perfect, as I mentioned before. But if you mix steel and aluminum, you get galvanic corrosion, which eats away at both. I made that mistake once on a bird feeder hook—steel bolt, aluminum washer, and within a year the whole hook broke off. Gross. So always check for galvanic compatibility if you’re mixing metals. If you’re not sure, just ask us—we’re happy to tell you, no pressure.
Now, let’s wrap this up with a quick cheat sheet, because I know you’re scrolling and want something to save. Next time you’re at the hardware store (or ordering from us, wink wink), ask yourself these 3 questions:
- What’s my bolt’s size? Match the washer’s ID to the bolt’s shank, add a tiny bit for wiggle room.
- What’s the surface/material I’m working with? Soft = big OD, outdoor/coastal = stainless or zinc, delicate = nylon.
- Do I need it to stop loosening? Vibration = lock or wave washer, general = flat washer.
That’s it. No fancy formulas, no confusing specs.
At the end of the day, the right washer doesn’t have to be expensive or fancy. It just has to fit your job’s needs. I’ve seen guys build a $1000 deck with $0.50 washers, and I’ve seen a $10k commercial project fail because someone grabbed a random washer. The difference is paying attention, not overcomplicating it.
If you’re still not sure, or you have a specific project where you’re stuck—no stress. Hit us up, tell me what you’re working on, what size bolts you’re using, and what environment it’s going in. We’ve been doing this long enough to spot the small mistake that’s tripping you up. No sales pitch, just straight-up advice from guys who’ve installed way more washers than we can count.

Thanks for sticking around—now go fix that wobbly fence, that leaky pipe, or that scratch-prone furniture. You’ve got this.
Turning References:
- Machine Design Handbook, 5th Edition – Fastener and Washer Specification Guidelines
- ASTM International Standard B18.21 – Compression Type Lock Washers
- Copper Development Association – Material Compatibility for Plumbing Fasteners
- International Association of Plumbing and Mechanical Officials (IAPMO) – Residential Fastener Installation Standards
Shanghai Megood Metal Products Co., Ltd.
As one of the most experienced bolts and screws manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale bulk bolts and screws made in China here and get quotation from our factory. Customized orders are welcome.
Address: Building 8, No. 1500 Huiren Road, Waigang Town, Jiading District, Shanghai
E-mail: liujingshco@163.com
WebSite: https://www.mgx-hardware.com/